Installation Manual
TL2803G – Installation Manual
3G2080(R)
Cellular Alarm Communicator – International
TL2803G(R)
Internet and HSPA Dual-Path Alarm Communicator - International
INSTALLATION GUIDE V4.1
For installation manual, visit www.dsc.com Warning: This manual contains information on limitations regarding product use and function and information on the limitations as to liability of the manufacturer.
WARNING: INSTALLER PLEASE READ CAREFULLY
Note to Installers The warnings on this page contain vital information. As the only individual in contact with system users, it is the installer’s responsi- bility to bring each item in this warning to the attention of all users of this system. System Failures This system has been carefully designed to be as effective as possi- ble. There are circumstances, however, involving fire, burglary, or other types of emergencies where it may not provide protection. Any alarm system of any type may be compromised deliberately or may fail to operate as expected for a variety of reasons. Some, but not all, of the reasons may be: Access by Intruders Intruders may enter through an unprotected access point, circumvent a sensing device, evade detection by moving through an area of insufficient coverage, disconnect a warning device, or interfere with or prevent the proper operation of the system. Component Failure Although every effort has been made to make this system as reliable as possible, the system may fail to function as intended due to the failure of a component. Compromise of Radio Frequency (Wireless) Devices Signals may not reach the receiver under all circumstances which could include metal objects placed on or near the radio path or delib- erate jamming or other inadvertent radio signal interference. Criminal Knowledge This system contains security features which were known to be effective at the time of manufacture. It is possible for persons with criminal intent to develop techniques which reduce the effectiveness of these features. It is important that your security system be reviewed periodically to ensure that its features remain effective and that it is updated or replaced if it is found that it does not provide the protection expected. Failure of Replaceable Batteries This system’s wireless transmitters have been designed to provide several years of battery life under normal conditions. The expected battery life is a function of the device environment, usage, and type. Ambient conditions such as high humidity, high or low temperatures, or large temperature fluctuations may reduce the expected battery life. While each transmitting device has a low battery monitor which identifies when the batteries need to be replaced, this monitor may fail to operate as expected. Regular testing and maintenance will keep the system in good operating condition. Inadequate Installation A security system must be installed properly in order to provide ade- quate protection. Every installation should be evaluated by a security professional to ensure that all access points and areas are covered. Locks and latches on windows and doors must be secure and operate as intended. Windows, doors, walls, ceilings and other building materials must be of sufficient strength and construction to provide the level of protection expected. A reevaluation must be done during and after any construction activity. An evaluation by the fire and/or police department is highly recommended if this service is available. Inadequate Testing Most problems that would prevent an alarm system from operating as intended can be found by regular testing and maintenance. The com- plete system should be tested weekly and immediately after a break- in, an attempted break-in, a fire, a storm, an earthquake, an accident, or any kind of construction activity inside or outside the premises. The testing should include all sensing devices, keypads, consoles, alarm indicating devices, and any other operational devices that are part of the system. Insufficient Time There may be circumstances when the system will operate as intended, yet the occupants will not be protected from an emergency due to their inability to respond to the warnings in a timely manner. If the system is remotely monitored, the response may not occur in time to protect the occupants or their belongings. Motion Detectors Motion detectors can only detect motion within the designated areas as shown in their respective installation instructions. They cannot discriminate between intruders and intended occupants. Motion detectors do not provide volumetric area protection. They have mul- tiple beams of detection and motion can only be detected in unob- structed areas covered by these beams. They cannot detect motion which occurs behind walls, ceilings, floor, closed doors, glass parti- tions, glass doors or windows. Any type of tampering whether inten- tional or unintentional such as masking, painting, or spraying of any material on the lenses, mirrors, windows or any other part of the detection system will impair its proper operation. Passive infrared motion detectors operate by sensing changes in tem- perature. However their effectiveness can be reduced when the ambi- ent temperature rises near or above body temperature or if there are intentional or unintentional sources of heat in or near the detection area. Some of these heat sources could be heaters, radiators, stoves, barbecues, fireplaces, sunlight, steam vents, lighting and so on. Power Failure Control units, intrusion detectors, smoke detectors and many other security devices require an adequate power supply for proper opera- tion. If a device operates from batteries, it is possible for the batteries to fail. Even if the batteries have not failed, they must be charged, in good condition and installed correctly. If a device operates only by AC power, any interruption, however brief, will render that device inoperative while it does not have power. Power interruptions of any length are often accompanied by voltage fluctuations which may damage electronic equipment such as a security system. After a power interruption has occurred, immediately conduct a complete system test to ensure that the system operates as intended. Security and Insurance Regardless of its capabilities, an alarm system is not a substitute for property or life insurance. An alarm system also is not a substitute for property owners, renters, or other occupants to act prudently to prevent or minimize the harmful effects of an emergency situation. Smoke Detectors Smoke detectors that are a part of this system may not properly alert occupants of a fire for a number of reasons, some of which follow. The smoke detectors may have been improperly installed or posi- tioned. Smoke may not be able to reach the smoke detectors, such as when the fire is in a chimney, walls or roofs, or on the other side of closed doors. Smoke detectors may not detect smoke from fires on another level of the residence or building. Every fire is different in the amount of smoke produced and the rate of burning. Smoke detectors cannot sense all types of fires equally well. Smoke detectors may not provide timely warning of fires caused by carelessness or safety hazards such as smoking in bed, vio- lent explosions, escaping gas, improper storage of flammable materi- als, overloaded electrical circuits, children playing with matches, or arson. Even if the smoke detector operates as intended, there may be cir- cumstances when there is insufficient warning to allow all occupants to escape in time to avoid injury or death. Telephone Lines If telephone lines are used to transmit alarms, they may be out of ser- vice or busy for certain periods of time. Also an intruder may cut the telephone line or defeat its operation by more sophisticated means which may be difficult to detect. Warning Devices Warning devices such as sirens, bells, horns, or strobes may not warn people or waken someone sleeping if there is an intervening wall or door. If warning devices are located on a different level of the resi- dence or premise, then it is less likely that the occupants will be alerted or awakened. Audible warning devices may be interfered with by other noise sources such as stereos, radios, televisions, air conditioners, other appliances, or passing traffic. Audible warning devices, however loud, may not be heard by a hearing-impaired per- son. 1 HSPA(3G) Alarm Communicator Installation Guide
IMPORTANT
This installation manual shall be used in conjunction with the control panel. All the safety instruc- tions specified within that manual shall be observed. The control panel is referenced as the “panel” throughout this document. This installation gu ide provides the basic wiring, programming and
troubleshooting information. Use th is guide in conjunction with th e installation manual available
online from the DSC website at www.dsc.com.The Internet and HSPA(3G) dual-path alarm com- municator is a fixed, wall-mounted unit, and shall be installed in the location specified in these instructions.The equipment enclosure must be fully assemb led and closed, with all the necessary screws/tabs, and secured to a wall before operation. Internal wiring must be routed in a manner that prevents: • Excessive strain on wire a nd on terminal connections, • Interference between power lim ited and non power limited wiring, • Loosening of terminal connections, or • Damage of conductor insulation. WARNING: Never install this equipment during a lightning storm. Safety Information The installer must instruct the system user on each of the following: • Do not attempt to service this product. Openin g or removing covers may expose the user to dangerous voltages or other risks. • Any servicing shall be referre d to service persons only. • Use authorized accessories only with this equipment. • Do not stay close to the equi pment during device operation. • Do not touch the external antenna. Model Information This manual covers the followi ng models of alarm communicators: TL2803GR, TL2803G, 3G2080R, 3G2080 (850/1900MHz operation), TL2803GR-EU, TL2803G-EU, 3G2080R-EU, 3G2080-EU (900/2100MHz operation) , TL2803G-AU, 3G2080-AU, TL2803GR-AU, and 3G2080R-AU (850/2100MHz operation) . References to model names TL2803G(R) and 3G2080(R) throughout this manual apply to all specified models unless stated differently. Models ending in “R” include a built-in RS-422 interface for connecting to local third party applications. The TL2803G(R)/3G2080(R) supports integration over cellular/IP, available with licensed 3 rd party product solutions. Specific programming for th e related programming sections is to be pro- vided by the 3 rd party. A current list of compatible 3 rd party solutions can be found at www.dsc.com. 3G2080(R): Is an HSPA (3G) cellular alarm communicator that sends alarm communication to Sur-Gard System I, II, III (SG- DRL3IP), IV (SG-DRL4IP), and 5 (SG-DRL5IP) central station receivers via an HSPA(3G)/GPRS digital cellular network. TL2803G(R): Is a dual-path HSPA(3G) Ethernet alarm communicator that sends alarm communi- cation to Sur-Gard System I, II, III, IV , and 5 central station receivers through Ethernet/Internet or an HSPA(3G)/GPRS digital cellular network. The communicator can be used as either a backup or primary communicator. The communicator supports Internet Protocol (IP) transmission of panel and communicator events over Ethernet/Internet and/or HSPA/GPRS. The cellular performance of the 3G2080(R) or TL2803G(R) communicator depends greatly on HSPA(3G)/GPRS network coverage in the local area. The unit should not be mounted in the final location without first performing the communicator placement test to determine the best location for radio reception (minimum of one green LED ON). Optional antenna kits (GS-15ANTQ, GS- 25ANTQ and GS-50ANTQ) are available from DSC to improve signal strength as required. NOTE: Prior to installation of the 3G2080(R) or TL2803G(R) communicator, confirm with your local service provider that the HSPA(3G)/GPRS network is available and active in the area where the communicator will be installed, and that radio signal strength (CSQ) is adequate.
GENERAL
2 HSPA(3G) Alarm Communicator Installation Guide Panel Mounting The following communicators are compatible with HS2016, HS2032, HS2064, and HS2128 panels: • 3G2080(R) (HSPA(3G)/GPRS only) • TL2803G(R) (Ethernet/Internet + HSPA(3G)/GPRS dual-path) Features • 128-bit AES encryption via cellu lar and Ethernet/Internet (NIST validation certificate number 2645). • Back up or primary cell ular alarm communication. • Automatically switches to 2G (EDGE/GPRS) if HSPA(3G) service is not available. • Ethernet LAN/WAN 10/100 BASE-T (TL2803G(R) only). • Fully redundant Ethernet/Internet and cellul ar dual-path alarm communication (TL2803G(R) only). • Full event reporting to central station. • Individual Internet a nd/or cellular periodic test transmission. • Integrated call routing. • Visual Verification (requir es System 5 receiver) • Remote firmware upgrade capabi lity of the communicator and panel firmware via Ethernet and/ or cellular. • Panel remote uploading/dow nloading support via cellular and Ethernet/Internet. • PC-LINK connection. • Programmable labels. • SIA and Contact ID (CID) formats supported. • Signal strength and trouble display LEDs. • Supervision heartbeats sent vi a cellular and Ethernet/Internet. • Command and Control by SMS. • Third party integration over cellular/IP. Technical Specifications • The TL2803G(R) can also be used with a compatible control unit listed for dual line security transmission when used in conjunction with a DACT or a Public Switched Data Network (PSDN) transmitter, where the PSDN provides the line security and is the primary line. In this mode, alarm signals are required to be sent simultaneously over both communication methods. EN50131-1 Installation Requirements For EN50131-1 compliant installations, the foll owing programming options shall be set as described. Supervision Heartbeat (required for ATS4 and ATS5): • [851][004] set to 0087h (135s heartbeat). NOTE: The compatible receiver at ARC location shall have supervision window programmed for 1800s (ATS4) or 180s (ATS 5). • [851][005] options 1,2 and 3 shall be enabled • [851][005] option 8 shall be enabled Test transmission (required for ATS3): • [851] System test options [026-029] shall be enabled (FF) for the communication paths available. • [851][124-125] and [224-225] shall be programmed with time of day for test transmission and
1440 minutes (24h) for test transmission cycle
Configuration of communication paths (all ATS classes)
• [300][001] select option 02 for auto routing (this will allow transmission of the events over all available communication paths in the system) • [380] enable option 5 (YES) for parallel transmission over all available communication paths (if redundant configuration is desired) • [382] enable option 5 (YES) this will enable the alternate communicator 3 HSPA(3G) Alarm Communicator Installation Guide • [384] enable the desired back-up configuration (receiver 2 back-up for receiver 1 or receiver 3 back-up for receiver 1). Ratings Compatibility NOTE: Enter [*][8][Installer Code][900] at keypad to view the panel version number. This Internet and HSPA dual-path alarm communicator shall be installed by service persons only (service person is defined as a person having the appropriate technical training and experience necessary to be aware of hazards to which that person may be exposed in performing a task and can also take measures to minimize the risks to that person or other persons). The Communicator shall be installed and used with in an environment that provides the pollution degree max 2, over- voltages category II, in non-hazardous, indoor locati ons only. This manual shall be used with the
installation manual of the panel which is connected to the communicator. All instructions specified
within the panel manual must be observed. All the local rules imposed by local electrical codes shall be observed and respected during instal- lation. Installing the Ethernet Cable (TL2803G(R) Only) A Category 5 (CAT 5) Ethernet cable must be run from a source with Ethernet/Internet connectiv- ity to the communicator module, inside the panel. The communicator end of the cable must be ter- minated with an RJ45 plug, which will connect to the comm unicator’s RJ45 jack after the communicator is installed. All re quirements for the installation of CAT 5 Ethernet cable must be observed for correct operation of the communicator, including, but not limited to, the following: • Do NOT strip off cable sheathing more than required for proper termination. • Do NOT kink/knot cable. • Do NOT crush cable with cable ties. Table 1: Communicator Ratings Model 3G2080(R) Cellular only
TL2803G(R)
Internet and Cellular Power Supply Ratings Input V oltage
10.8-12.5 VDC
Power is supplied from the panel’s PC-Link header or a PCL-422 module in remote cabinet installations. In remote cabinet installations, the PCL-422 module located with the communicator is powered by either an HSM2204 or an HSM2300. Refer to the PCL-422 installation instructions for details. Current Consumption Standby Current 90mA @ 13.66V 120mA @ 13.66V Alarm (Transmitting) Current 400mA @ 12V Operating Frequency 900MHz, 1800MHz, 2100MHz Typical Antenna Gain 2dB i Environmental Specifications Operating Temperature -10°C to 55°C Humidity 5% ~ 93% relative humidity, non-condensing Mechanical Specifications Board Dimensions (mm) 100 × 150 × 15 100 × 150 × 15 Weight (grams) with bracket 310 320 Table 2: Compatible Receivers and Panels Communicator Receiver/ Panel Description
3G2080(R)
TL2803G(R)
Receiver • Sur-Gard System I Receiver, version 1.13+ • Sur-Gard System II Receiver, version 2.10+ • Sur-Gard SG-DRL3-IP, version 2.30+ (for Sur-Gard System III Receiver) • Sur-Gard SG-DRL4-IP version 1.20+ (for Sur-Gard System IV Receiver) • Sur-Gard SG-DRL5-IP version 1.00+ (for Sur-Gard System 5 Receiver) Panel
• HS2016
• HS2032
• HS2064
• HS2128
COMMUNICATOR INSTALLATION CONFIGURATION
4 HSPA(3G) Alarm Communicator Installation Guide • Do NOT untwist CAT5 pairs more than ½ in. (1.2cm). • Do NOT splice cable. • Do NOT bend cable at right angles or make any other sharp bends. NOTE: CAT5 specification requires that any cable bend must have a minimum 2 in. (5 cm) bend radius. Maximum length of CAT 5 cable is 328 ft. (100 m). Inserting and Removing the SIM Card
1. Remove the front cover of the panel to access SIM holder.
2. Remove power from the panel and disc onnect the battery and telephone line.
3. On the SIM card holder, push gently to slide the cover downwards to OPEN. This will unlatch
the SIM card holder on the top edge of the communicator PCB. (See Figure 3).
4. Tilt the top of the SIM card holder downwards to access the SIM card.
NOTE: The SIM can be damaged by bending or scratching contacts. Use caution when handling SIM cards.
5. Insert or remove the SIM card, noting the orie ntation of the notches on the SIM card and the
SIM card holder.
6. When inserting a SIM card, insert the card in the proper orientation and gently push the SIM
card holder down and slide the holder as indicated by the arrow on SIM holder, to LOCK.
7. Reconnect the backup battery and telephone line, apply AC power to panel, and replace the
panel cover. Running the RS-422 Cable (R Models Only) When installing the communicator for use with 3r d party applications an RS-422 cable must be connected between the 3rd party device and the communicator module. NOTE: Maximum cable length for RS-422 cable is 1,000 ft. (305 m). Please refer to the installation manual for the 3rd party device for wiring instructions. Installing Communicator with HS2016, HS2032, HS2064, and HS2128 Panel NOTE: Before installing communicator or inserting/removing SIM, ensure that system power is OFF and telephone line is disconnected.
1. To assemble supplied mounting bracket, perform the following: (See Figure 1).
a. Remove the 4 white plastic standoffs from the bag pro- vided with the communicator kit. b. Insert the 4 standoffs through the back of the mounting bracket, into the holes at each corner. (The antenna mount- ing tab should be facing away from you). c. Place the bracket on a flat, solid surface. Hold the com- municator component side up and orient the 4 holes on the communicator with the 4 standoffs protruding from the
INSTALLING CELLULAR/ETHERNET COMMUNICATOR IN
PANEL
DG0009744
Brass Washer Nylon washer (flat) Nylon Washer with bushing (thicker flat washer) Brass nut Antenna Mounting Tab Mounting Holes Mounting Holes Antenna Cable Mounting Plate External Antenna Screw Thread Communicator Board Mounting Plate Stand Off Figure 1:Communicator Mounting Bracket 5 HSPA(3G) Alarm Communicator Installation Guide bracket. Push the communicator firmly and evenly onto the standoffs until it is securely attached to the mounting bracket. d. Remove the panel front cover. e. Remove and discard the circular knockout located in the top-right section of the panel. (This hole will be used for the connection of the supplied radio antenna). f. Connect the supplied 5” (12. 7 cm) antenna cable to the radio, by passing the connector through the hole on the back of the mounting bracket to the communicator board. Push the antenna connector firmly into the socket on the cellular radio. (See Figure 3).
2. Install the Communica tor into the panel:
a. Attach one end of the PC-LINK cable to th e panel PC-LINK header on the panel (red wire goes on the right-hand pin of the panel PC-LINK_2 header (see Figure 3)). b. Insert the assembled communicator into the panel. NOTE: Ensure that the threaded antenna connection point is visible through the knockout hole at the top right of the panel. c. Place the nylon washer with bushing (thick fl at washer) onto the threaded section of the antenna cable. Insert the threaded section through the antenna mounting knockout hole at top right of panel. d. Place the second nylon washer (flat), followe d by the brass washer and the brass nut, onto the threaded section of the cable, outside the panel. Tighten the assembly by hand only (fin- ger tight only- do not over tighten the antenna assembly). e. Locate the screw hole on the right side wall of the panel. See Figure 2 (screw). Line up the assem- bled communicator with the right side wall of the panel and, using the scre w provided, secure the mounting bracket to the panel. f. Attach the other end of the PC-LINK cable to the communicator (black wire goes on pin 1 of the communicator). g. Using light pressure (finge r tight only), attach the supplied white quad band whip antenna to the threaded antenna connection point at the top of the panel. WARNING! - 3G2080(R)/TL2803G(R) modules are power limited. Do not route any wiring over the cir- cuit board. Maintain at least 1in. (25.4mm) separa- tion between circuit board and wiring. A minimum of ¼ in. (7mm) separation must be maintained at all points between non-power limited wiring and power limited wiring.
3. To electrically connect the communicator to the panel, perform the following steps (SeeFigure 3).
a. Disconnect both AC power and battery connections from the panel, and disconnect tele- phone line. b. Confirm that the SIM card is inserted in the holder and locked. PC-Link cable connector screw quad band whip antennaGSM Radio
RJ-45
UA601
Use light pressure to attach antenna finger tight only.
HS2016/2032/2064/2128
Figure 2:HS2016/2032/2064/2128 Control Panel 6 HSPA(3G) Alarm Communicator Installation Guide
4. Install network cable (TL2803G(R) only). Route the CAT 5 Ethernet cable through back of the
panel and plug it into the communicator’s RJ45 jack. NOTE: Before leaving the premises the Ethernet communication lines must first be connected to an approved (acceptable to local authorities) type NID. All wiring shall be performed according to the local electrical codes.
5. Install the RS-422 connections (R models only). If using the communicator with a 3rd party
device, wire the connections as per the table below: NOTE: The GND connection is optional. DSC recommends connecting GND wire at both ends.
6. Perform the following steps for initial power on of the panel with the communicator installed:
a. Reconnect the AC power, telephone line, and battery + connector to the panel. (The communicator and panel will power up together). b. Observe that the communicator’s red and yellow LEDs are flashing together while it initial- izes. The red and yellow LEDs will continue to flash until the communicator has success- fully communicated to all programmed receivers. NOTE: During radio reset, the two green LEDs will flash alternately. NOTE: Initialization may take several minutes to complete. Red and yellow LEDs will flash together during initialization. Do not continue to next step until the red and yellow LEDs have stopped flashing. (If only the yellow LED is flashing, there is a communicator trou- ble and the green LEDs are not valid for communicator placement test). Correct trouble Table 3: RS-422 Connections 3rd Party Device Communicator
TX+ RX+
TX- RX-
RX+ TX+
RX- TX-
GND (Optional) GND Figure 3:Communicator Wiring Diagram
AUDIO/DEFAULT
DSC
UA601
PC-LINK COM
TL2803G(R)
3G2080(R)
AC AC Z1 COM Z2 Z3 COM Z4 Z5 COM Z6 Z7 COM Z8AUX+
BELL +
PGM1 PGM3 RING T-1
HS2016/2032/2064/2128
3G Radio
UA621
To external antenna Input Ratings:
+10.8V ~ +12.5 VDC
90mA(3G2080(R))/120mA(TL2803G(R)) standby; 400mA alarm DSC Panel min. power requirements: - 16.5 VAC 40 VA transformer; - 12 VDC 7Ah battery Jumper pins 4 and 5 to reset.
L
o c k 1 From NID
TL2803G(R)
Use only CAT5 Supervised
RJ-45
GRN
YEL
TIP R-1
BLK
RED
AUX -
BELL -
EGND
TX+
GND
TX-
RX+
RX-
SHLD
SIM
Network Link
YELLOW
PGM2 PGM4
Maximum cable length
100 m (328 ft)
PCLINK_2
Red Red
RS-422
To 3rd party device 7 HSPA(3G) Alarm Communicator Installation Guide indicated by flashes on yellow LED before continuing. (See Table 8 for troubleshooting assistance).
7. Perform the communicator placement test below.
8. Mount the panel in final locati on indicated by placement test.
3G2080(R) and TL2803G(R) only To confirm that the cellular antenna location is suitable for radio operation, perform the placement test as follows: NOTE: You may need to relocate the panel or install an optional extension antenna during this procedure, if the radio signal strength is too low.
1. Confirm that the yellow LED on the communicator is not flashing. A flashing yellow LED indi-
cates trouble on the communicator. See Table 8 to troubleshoot and correct the cause of this trou- ble before continuing to the next step.
2. Observe that the strength of the radio signal on the yellow LED and the 2 green LEDs on the
communicator meet or exceed the minimum signal level requirement. Minimum signal level: The yellow LED is OFF and the green LED 1 (furthest from the yellow LED) is ON. (i.e., not flashing) for the panel location to be acceptable. See table for “Radio Signal Strength” on page 9 for the interpretation of the receiver signal strength on LEDs. Cellular Signal Strength Display - LCD Keypad only The cellular network signal strength can be checked on the keypad LCD screen by entering installer programming section [850 ]. The LCD will indicate the SIM card activation status fol- lowed by up to five bars of signal strength. This display will automatically update every three sec- onds. Refer to “Radio Signal Strength” on page 9 for the relationship be tween signal strength bars, CSQ level, and signal level in dBm. NOTE: If the required signal strength is too low with the panel in its current location, the panel must be relocated or an external antenna is required. a. If required, the following cellular extension an tenna kits are available to the installer: • GS-15ANTQ - 4.57m (15’) Internal Antenna Extension Kit (suitable for interior mounting only). • GS-25ANTQ - 7.62m (25’) External Antenna Extension Kit (suitable for interior/exterior mounting). • GS-50ANTQ - 15.24m (50’) External Antenna Extension Kit (suitable for interior/exterior mounting). Specific instructions for the installation of the extension antenna are included with the kit. Observe all the electrical safety instructions regarding the installation of the antenna. All the wiring of the equipment shall be fully compliant with the local rules and regulations.
3. If required, install the antenna extension and perform the following steps to determine the best
location for placement of the antenna: a. Disconnect the white whip antenna from the panel. b. Attach one end of the antenna extension cabl e to the threaded antenna connector on the panel and the other end to the external antenna.
4. Move the extension antenna to various locati ons while observing the two green LEDs on the
panel. a. Continue to reposition the extension antenn a until you receive an acceptable (minimum one green LED ON solid) signal strength.
COMMUNICATOR PLACEMENT TEST
Table 4: Signal Strength Display Description Display SIM card active and current signal strength SIM card inactive and current signal strength Radio not registered
OR AND
8 HSPA(3G) Alarm Communicator Installation Guide NOTE: Minimum strength is: green LED 1 flashing and yellow LED off. If green LED 1 is flashing, relocation should be considered. b. Mount the supplied ante nna extension bracket at the loca tion that provides the best signal strength.
5. Alternately, reposition the pane l to improve signal strength. Dismount the panel and move it to
another location to achieve the required signal strength. If the panel is relocated to improve sig- nal strength, mount it in the new location.
6. When final panel/antenna location is determined, continue at the Initial Panel Programming-
section. NOTE: If the SIM card is not activated, the placement test will indicate the signal strength of the nearest cellular tower. NOTE: In between displaying signal strength, the signal strength LEDs will flash alternately if an inactive SIM card is used. The flashing indicates that the module is attempting to attach to the cellular network and will only last a short while. HS2016/2032/2064/2128 Initial Programming Please refer to panel manual section ‘Alternate Communicator Set-up’ for details.
1. In panel section [ 377] ‘Communication V ariables’, subsection [002] ‘Communication Delays’,
sub-subsection [1] ‘Communication Delay’, program 060 (seconds).
2. In panel section [ 382] ‘Communicator Option 3’ set option [5] ON
3. In panel sections [300] subsections [001] to [004], program the subsection with 02 to 06
NOTE: Refer to the panel manual for additional information.
4. In panel section [350] ‘Comm unications Formats’, program the communication format as: CID
(03) or SIA FSK (04).
5. In panel sections [311] - [318] ‘Partition Call Directions’, program the call direction options for
the system.
6. In panel section [401] ‘DLS /SA Options’, set toggle option [2] ‘User Enable DLS’ to ON in
order to perform panel DLS session through cellular or Ethernet. NOTE: Before leaving the premises, the installer should verify all programmed communications paths. See programming options section [851][901] to send immediate test transmissions. Communicator Troubles displayed on a HS2016/2032/2064/2128 The communication trouble is the only trouble that will appear on the keypad Liquid Crystal Dis- play (LCD) when encountered by a communica tor installed in a HS2016/2032/2064/2128. For more information about troubles on the communica tor module, refer to the panel event buffer or by accessing *2 to view the individual trouble types.
INITIAL PANEL PROGRAMMING
Table 5: Dialing Strings Value Communication Method
02 Auto Routing
03 Ethernet 1
04 Ethernet 2
05 Cellular 1
06 Cellular 2
9 HSPA(3G) Alarm Communicator Installation Guide The communicator has 4 on-board LED indicators. These include 1 yellow trouble LED, 1 red net- work connection status LED, and 2 green signal strength LEDs. The LED meaning is described in this section. Yellow Trouble LED This yellow LED will flash to i ndicate a trouble on the unit. The number of flashes indicates the type of trouble. See the table below for the coded flashes and the conditions which will activate the trouble status LED. NOTE: Only the highest priority trouble (2 flashes is the highest priority trouble) is indicated. When this trouble is restored, the next highest trouble will indicate, if present. This will continue until all troubles have been cleared (yellow LED is not flashing). Red Network Connection Status LED
TL2603G
BLINKING: Indicates communications in progress. • Once quickly for outgoing Ethernet transmission. • Twice quickly to indicate incoming Ethernet ACK/NACK. OFF: This is the normal state of the red networ k connection status LED. There are no network connection issues present. ON: There is a problem with the Ethernet or the cellular network connection. LED will be ON if any of the following occur: • Ethernet cable is not connected, • DHCP configuration times out, • Unit fails to get an IP addres s from the cellular network, or • Cellular connection has been reset. (Green LED 1) (Green LED 2) and (Yellow LED) Signal Strength NOTE: If the yellow LED is flashing, signal strength in table below is not valid. See Table 8 for troubleshooting flashing yellow LED.
COMMUNICATOR STATUS LEDS
Table 6: Yellow Trouble Status LED # of Flashes Trouble # of Flashes Trouble
2 Panel Supervision Trouble 8 Receiver Supervision Trouble
4 SIM Lock Trouble 9 FTC Trouble
5 Cellular Trouble 10 Not Applicable
6 Ethernet Trouble 12 Module Configuration Trouble
7 Receiver Not Available Trouble
Table 7: Radio Signal Strength Signal Strength
CSQ
Level Yellow
LED
Green Led 2 Green
LED 1
Signal Level dBm Action Required Radio Not Ready N/A N/A Alternate Flashing Alternate Flashing N/A If this status persists and the yellow LED shows 5 flashes, confirm that the SIM card is active. No Signal 0 ON OFF OFF -108.8 Check all antenna connections. Confirm cellular service is active in area. Relocate panel or install external antenna.
1 Bar 1 - 4 Flashing
See Note OFF Flashing -108 ~ -103 Relocate panel or install external antenna if yellow trouble LED has:
5 flashes.2 Bars 5 - 6 OFF OFF Flashing -102 ~ -99
3 Bars 7 - 10 OFF OFF ON -98 ~ -91
Location is OK. Cellular signal strength is greater than CSQ 7.
4 Bars 11-13 OFF Flashing ON -90 ~ -85
5 Bars 14 + OFF ON ON -84 and
higher 10 HSPA(3G) Alarm Communicator Installation Guide NOTE: The communicator will indicate cellular trouble (yellow LED = 5 flashes) if the calcu- lated average CSQ Level is 4 or less. The communicator signal strength can be viewed remotely with Connect24. Network Activity LEDs (Red and Green)TL2603G only • Ethernet Activity: Red LED will blink quickly once for transmit, or twice for receive. • Cellular Activity: Green LED 2 will blink quickly once for transmit, or twice for receive
COMMUNICATOR TROUBLESHOOTING
Table 8: Trouble Indications Trouble Indication Trouble Indicator Digit Possible Causes Possible Trouble Solution No Indication N/A No Power • Check the power connections between the panel and the communicator. • Confirm PC-LINK cable is properly installed between communicator and panel. Yellow LED – ON Solid N/A No Signal • Confirm that cellular network service is active in your area. • Ensure the antenna is securely connected to the radio. Check antenna stub cable is securely connected to the radio. • If an external antenna is used, ensure the antenna is securely screwed on to the antenna cable connector. Check external antenna for damage or open/short. Trouble LED –
2 Flashes 02
Panel Supervision Trouble • Check section [382] toggle option[ 5] is ON (Alternate Communicator Enabled). • Ensure the PC-LINK cable between the panel and communicator is connected properly (not reversed) and is securely in place. Yellow LED –
5 Flashes 05 Cellular Trouble
• Confirm that cellular service is available and active in your area. • Check all antenna connections. • Ensure average radio signal strength is CSQ 5 or higher. (See Table 7 ). • Ensure the SIM card is properly inserted into the SIM card holder. • Ensure the SIM card has been activated (could take up to 24 hrs after install). • If this trouble persists, you must relocate the panel (and communicator) or install an external antenna extension kit. Yellow LED –
6 Flashes 06 Ethernet
Trouble • Check with your ISP to confirm Internet service is active in your area. • Ensure your Ethernet cable is securely inserted into the RJ45 jack of the com- municator and the hub/router/switch. • Check the link light on the hub/router/switch is ON. If link light is OFF, start the hub/router/switch. • If DHCP is used, ensure that the unit has an assigned IP address from the server. In Section [851] [992] verify a valid IP address is programmed. If not, contact the network administrator. • If problem persists, replace the Ethernet cable and RJ45 connector. Yellow LED –
7 Flashes 07 Receiver Not
Available • Ensure that the Ethernet path has Internet connectivity. • If using a static IP address, confirm that the gateway and subnet mask are entered correctly. • If the network has a firewall, ensure the network has the programmed outgoing ports open (default UDP port 3060 and port 3065). • Ensure that all the receivers are programmed for DHCP or have the proper IP address and port number. • Ensure the cellular receiver APNs have been programmed with the access point name provided by your cellular provider. • If Common Mode is used, and only one path is initialized while the other path is not successful, generate a manual test transmission over both paths or power cycle the communicator to recover the ‘Receiver Not Available’ trouble. Yellow LED –
8 Flashes 08
Receiver Supervision Trouble • This trouble is indicated when supervision is enabled and the unit is not able to successfully communicate with the receiver. • If this trouble persists, contact your central station. Yellow LED -
9 Flashes 09 FTC Trouble
• The unit has exhausted all communica tions attempts to all programmed receivers for events generated by the communicator. • Restart the system. If trouble persists, contact your dealer. Yellow LED –
12 Flashes 0C
Module
Configuration
Trouble • This indication appears when section [021] system account code or sections [101]; [111]; [201]; and [211] receiver account code have not been programmed. Ensure that a valid account code has been entered in these sec- tions. All LEDs flash- ing together N/A Boot Loader Failed • Disconnect power, then reconnect power to the communicator module. Red and Yellow LEDs flashing together N/A Initialization Sequence • The unit is still initializing please wait while the unit gets its programming and establishes a connection to all programmed receivers. Note: This process may take several minutes to complete. 11 HSPA(3G) Alarm Communicator Installation Guide System Options [001] Ethernet IP Address Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [002] Ethernet IP Subnet Mask Default (255.255.255.000) |____|____|____||____|____|____||____|____|____||____|____|____| [003] Ethernet Gateway IP Address Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [004] Receiver Supervision Interval Default (0087/135) Valid range: 0000 - FFFF. |____|____|____|____| [005] System Toggle Options |____| [1] Ethernet Receiver 1 Supervised Default (OFF). |____| [2] Cellular Receiver 1 Supervised Default (OFF). |____| [3] Supervision Type Default (OFF). |____| [4] Primary Communications Path. Default (OFF) TL2803G(R); (ON) 3G2080(R). |____| [5] Redundant Communications Default (OFF). |____| [6] Remote Firmware Upgrade Default (ON). |____| [7] Alternate Test Transmission Default (OFF). |____| [8] Cellular Low Signal Trouble Default (OFF). [006] System Toggle Options 2 |____| [1] Ethernet Receiver 1 Enabled Default (ON). |____| [2] Ethernet Receiver 2 Enabled Default (ON). |____| [4] Cellular Receiver 1 Enabled Default (ON). |____| [5] Cellular Receiver 2 Enabled Default (ON). |____| [7] DLS Over Cellular Default (ON). |____| [8] Network Trouble Suppression (OFF). [007] DNS Server IP 1 Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [008] DNS Server IP 2 Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [009] Language Default (01); Program label language 01-29 |____|____|
Programming Options
[010] System Toggle Options 3 |____| [1] Reserved. |____| [2] Visual Verification Default (OFF). |____| [3] Reserved. [011] Installer Code Default (CAFE) Valid range: 0000 - FFFF. |____|____|____|____| [012] DLS Incoming Port Default (0BF6/3062) Valid range: 0000 - FFFF. |____|____|____|____| [013] DLS Outgoing Port Default (0BFA/3066) Valid range: 0000 - FFFF. |____|____|____|____| [015] DLS Call-Up IP Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [016] DLS Call-Up Port Default (0000) Valid range: 0000 - FFFF. |____|____|____|____|
ETHERNET/CELLULAR PROGRAMMING WORKSHEETS
The programming sections described in this document can be viewed at the keypad LCD. To start
programming enter: [*][8][installer code] [851] [section number] , where section number is the 3
digit section number referenced in this section. The programming worksheets at the end of this doc- ument can be used to record the new values wh en programming changes have been made from the default values. Only Green LEDs flashing N/A Hardware Default Jumper • The hardware default jumper is installed and must be removed. See Figure 3. Green LEDs alternating N/A Radio Reset or Radio Initializa- tion • If this status persists and the yellow LED shows 5 flashes, confirm that the SIM card is active.
ETHERNET/CELLULAR PROGRAMMING OPTIONS
Table 8: Trouble Indications Trouble Indication Trouble Indicator Digit Possible Causes Possible Trouble Solution 12 HSPA(3G) Alarm Communicator Installation Guide [020] Time Zone Default (00) Valid range: 00 - 99. |____|____|____|____| [021] Account Code Default (FFFFFF) Valid range: 000001 - FFFFFE. |____|____|____|____|____|____| [022] Communications Format Default (04) Program 03 (CID), 04 (SIA). |____|____| [023] Panel Absent Trouble Default (FF); Program 00 disable or FF enable. |____|____| [024] Panel Absent Trouble Restore Default (FF) Program 00 disable or FF enable. |____|____| System Test Options [026 - 029] [026] Ethernet 1 Transmission Default (FF) Program 00 disable or FF enable. |____|____| [027] Ethernet 2 Transmission Default (00) Program 00 disable or FF enable. |____|____| [028] Cellular 1 Transmission Default (FF) Program 00 disable or FF enable. |____|____| [029] Cellular 2 Transmission Default (00) Program 00 disable or FF enable. |____|____| [030] FTC Restore Default (FF) Program 00 disable or FF enable. |____|____| [037] System Firmware Update Fail Default (FF) Program 00 disable or FF enable. |____|____| [095] SA Incoming Local Port Default (0000) Valid range: 0000 - FFFF. |____|____|____|____| [096] SA Outgoing Local Port Default (0000) Valid range: 0000 - FFFF. |____|____|____|____| [097] SA User Call Up IP Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [098] SA User Call Up Port Default (0000) Valid range: 0000 - FFFF. |____|____|____|____| [099] SA Password Default (FFFFFFFF) Valid range: 00000000 - FFFFFFFF. |____|____|____|____|____|____|____|____| Ethernet Receiver 1 Options [101] Ethernet Receiver 1 Account Code Default (0000000000) Valid range: 0000000001 - FFFFFFFFFE. |____|____|____|____|____|____|____|____|____|____| [102] Ethernet Receiver 1 DNIS Default (000000) Valid range: 000000 - FFFFFF. |____|____|____|____|____|____| [103] Ethernet Receiver 1 Address Default (127.000.000.001) |____|____|____||____|____|____||____|____|____||____|____|____| [104] Ethernet Receiver 1 UDP Remote Port Default (0BF5/3061) Valid range: 0000 - FFFF. |____|____|____|____| [105] Ethernet Receiver 1 UDP Local Port Default (0BF4/3060)Valid range: 0000 - FFFF. |____|____|____|____| [106] Ethernet Receiver 1 Domain Name Default ( ) 32 ASCII characters. ________________________________ Ethernet Receiver 2 Options [111] Ethernet Receiver 2 Account Code Default (0000000000) Valid range: 0000000001 - FFFFFFFFFE. |____|____|____|____|____|____|____|____|____|____| [112] Ethernet Receiver 2 DNIS Default (000000) Valid range: 000000 - 0FFFFF. |____|____|____|____|____|____| [113] Ethernet Receiver 2 Address Default (000.000.000.000) |____|____|____||____|____|____||____|____|____||____|____|____| [114] Ethernet Receiver 2 UDP Remote Port Default (0BF5/3061) Valid range: 0000 - FFFF. |____|____|____|____| [115] Ethernet Receiver 2 UDP Local Port Default (0BF9/3065) Valid range: 0000 -FFFF. |____|____|____|____| [116] Ethernet Receiver 2 Domain Name Default ( ) ____________________________________ 13 HSPA(3G) Alarm Communicator Installation Guide Ethernet Options [124] Ethernet Test Transmission Time Default (9999) Valid: 00-23(HH); 00-59(MM) |____|____|____|____| [125] Ethernet Test Transmission Cycle Default (000000) Valid range: 000000 - 999999 minutes. |____|____|____|____|____|____| Cellular Receiver 1 Options [201] Cellular Receiver 1 Account Code Default (0000000000) Valid range: 0000000001 - FFFFFFFFFE. |____|____|____|____|____|____|____|____|____|____| [202] Cellular Receiver 1 DNIS Default (000000) Valid range: 000000 - 0FFFFF. |____|____|____|____|____|____| [203] Cellular Receiver 1 Address Default (000.000.000.000). Valid range: 000-255. |____|____|____||____|____|____||____|____|____||____|____|____| [204] Cellular Receiver 1 Port Default (0BF5/3061) Valid range: 0000 - FFFF. |____|____|____|____| [205] Cellular Receiver 1 APN Default ( ) 32 ASCII characters. __________________________________________________ [206] Cellular Receiver 1 Domain Name Default ( ) 32 Character ASCII characters. __________________________________________________ Cellular Receiver 2 Options [211] Cellular Receiver 2 Account Code Default (0000000000) Valid range: 0000000001 - FFFFFFFFFE. |____|____|____|____|____|____|____|____|____|____| [212] Cellular Receiver 2 DNIS Default (000000) Valid range: 000000 - 0FFFFF. |____|____|____|____|____|____| [213] Cellular Receiver 2 Address Default (000.000.000.000) Valid segment range: 000-255 |____|____|____||____|____|____||____|____|____||____|____|____| [214] Cellular Receiver 2 Port Default (0BF5/3061) Valid range: 0000 - FFFF. |____|____|____|____| [215] Cellular Receiver 2 APN Default ( ) 32 ASCII characters. __________________________________________________ [216] Cellular Receiver 2 Domain Name Default ( )
32 ASCII characters.
__________________________________________________ Cellular Options [221] Cellular Public Access Point Name Default ( ) 32 ASCII characters __________________________________________________ [222] Cellular Login User Name Default ( ) 32 ASCII characters. __________________________________________________ [223] Cellular Login Password Default ( ) 32 ASCII characters. __________________________________________________ [224] Cellular Test Transmission Time of Day Default (9999) Valid range: 00 - 23 hrs. (HH) 00 - 59 min. (MM). |____|____|____|____| [225] Cellular Test Transmission Cycle Default (000000) Valid range: 000000 - 999999 minutes. |____|____|____|____|____|____| [226] Network Trouble Delay Default (0F) Valid entries from, 00 to FF. |____|____| Event Notification/Integration Options [301] SMS Toggle Options |____| [1] SMS Notification (ON). |____| [2] Reserved |____| [3] SMS Command and Control Default (ON). |____| [4] Reserved |____| [5] SMS Character Format (OFF) |____| [6] Long SMS Message Handling Default (OFF). |____| [7] Reserved |____| [8] Reserved [307] SMS Delimiter Default (20) Valid range: 00 to FF. The value ‘20’ hexadecimal represents a space. |____|____| [311]-[342] SMS Phone Number 1-32 __________________________________________________ 14 HSPA(3G) Alarm Communicator Installation Guide [343]-[374] SMS Phone Number 1-32 Toggle Options |____| [1] SMS Notification Alarm/Restore Default (OFF). |____| [2] SMS Notification Tamper/Restore Default (OFF). |____| [3] SMS Notification Opening/Closing Default (OFF). |____| [4] SMS Notification System Maintenance Default (OFF). |____| [5] SMS Notification System Test Default (OFF) |____| [6] SMS Notification Internal Events Default (OFF). |____| [7] SMS Notification Enabled Default (OFF). |____| [8] SMS Command and Control Enabled Default (ON). [375]-[406] SMS Phone Number 1-32 Partition Option Default (00) Valid range: 00 - FF.
00 - Global; 01-32 - Partition; FF - Disabled
|____|____| External Event Label Program- ming [451] Burglary Alarm Default (Burglary Alarm) __________________________________ [452] Burglary Alarm Restore Default (Burglary Alarm Restore) __________________________________ [453] Fire Alarm Default (Fire Alarm) __________________________________ [454] Fire Alarm Restore Default (Fire Alarm Restore) __________________________________ [455] 24 Hour Alarm Default (24 Hour Alarm) __________________________________ [456] 24 Hour Alarm Restore Default (24 Hour Alarm Restore) __________________________________ [457] Holdup Alarm Default (Holdup Alarm) __________________________________ [458] Holdup Alarm Restore Default (Holdup Alarm Restore) __________________________________ [459] Gas Alarm Default (Gas Alarm) __________________________________ [460] Gas Alarm Restore Default (Gas Alarm Restore) __________________________________ [461] High Temperature Alarm Default (High Temperature Alarm) __________________________________ [462] High Temperature Alarm Restore Default (High Temperature Alarm Restore) __________________________________ [463] Medical Alarm Default (Medical Alarm) __________________________________ [464] Medical Alarm Restore Default (Medical Alarm Restore) __________________________________ [465] Panic Alarm Default (Panic Alarm) __________________________________ [466] Panic Alarm Restore Default (Panic Alarm Restore) __________________________________ [467] Emergency Alarm Default (Emergency Alarm) __________________________________ [468] Emergency Alarm Restore Default (Emergency Alarm Restore) __________________________________ [469] Sprinkler Alarm Default (Sprinkler Alarm) __________________________________ [470] Sprinkler Alarm Restore Default (Sprinkler Alarm Restore) __________________________________ [471] Water Level Alarm Default (Water Level Alarm) __________________________________ [472] Water Level Alarm Restore Default (Water Level Alarm Restore) __________________________________ [473] Low Temperature Alarm Default (Low Temperature Alarm) __________________________________ [474] Low Temperature Alarm Restore Default (Low Temperature Alarm Restore) __________________________________ [475] Fire Supervisory Default (Fire Supervisory) __________________________________ [476] Fire Supervisory Restore Default (Fire Supervisory Restore) __________________________________ [477] CO Alarm Default (CO Alarm) __________________________________ [478] CO Alarm Restore Default (CO Alarm Restore) __________________________________ [479] Flood Alarm Default (Flood Alarm) __________________________________ [480] Flood Alarm Restore Default (Flood Alarm Restore) __________________________________ [481] Quick Bypass Alarm Default (Quick Bypass Alarm) __________________________________ [482] Quick Bypass Alarm Restore Default (Quick Bypass Alarm Restore) __________________________________ 15 HSPA(3G) Alarm Communicator Installation Guide [483] Aux Alarm Default (Aux Alarm) __________________________________ [484] Aux Alarm Restore Default (Aux Alarm Restore) __________________________________ [485] Zone Expander Supervisory Alarm Default (Zone Expander Supervisory Alarm) __________________________________ [486] Zone Expander Sup. Alarm Restore Default (Zone Expander Sup. Alarm Restore) __________________________________ [487] Duress Alarm Default (Duress Alarm) __________________________________ [500] Account Label Default (Security System) __________________________________ [501] General System Tamper Default (General System Tamper) __________________________________ [502] General System Tamper Restore Default (General System Tamper Restore) __________________________________ [503] General System Trouble Default (General System Trouble) __________________________________ [504] General System Restore Default (General System Restore) __________________________________ [505] Panel AC Power Trouble Label Default (AC Power Trouble) __________________________________ [506] Panel AC Power Restore Label Default (AC Power Restore) __________________________________ [507] Panel Auxiliary Power Trouble Default (Auxiliary Power Trouble) __________________________________ [508] Panel Auxiliary Power Restore Default (Auxiliary Power Restore) __________________________________ [509] Panel Battery Trouble Default (Battery Trouble) __________________________________ [510] Panel Battery Restore Default (Battery Trouble Restore) __________________________________ [511] Panel Bell Circuit Trouble Default (Bell Circuit Trouble) __________________________________ [512] Panel Bell Circuit Restore Default (Bell Circuit Restore) __________________________________ [513] Panel Telephone Line Trouble Default (Telephone Line Failure) __________________________________ [514] Panel Telephone Line Restore Default (Telephone Line Restore) __________________________________ [515] Fail to Communicate Trouble Default (Fail to Communicate Trouble) __________________________________ [516] Fail to Communicate Restore Default (Fail to Communicate Restore) __________________________________ [517] Fire Trouble Default (Fire Trouble) __________________________________ [518] Fire Trouble Restore Default (Fire Trouble Restore) __________________________________ [519] Zone Tamper Default (Zone Tamper) __________________________________ [520] Zone Tamper Restore Default (Zone Tamper Restore) __________________________________ [521] Zone Fault Default (Zone Fault) __________________________________ [522] Zone Fault Restore Default (Zone Fault Restore) __________________________________ [523] Alternate Communicator Trouble Default (Alternate Communicator Trouble) __________________________________ [524] Alternate Communicator Restore Default (Alternate Communicator Restore) __________________________________ [525] Module Trouble Default (Module Trouble) __________________________________ [526] Module Trouble Restore Default (Module Trouble Restore) __________________________________ [527] Wireless/AML Device Trouble Default (Device Trouble) __________________________________ [528] Wireless/AML Device Restore Default (Device Trouble Restore) __________________________________ [551] Disarmed By Default (Disarmed By) __________________________________ [552] Armed By Default (Armed By) __________________________________ [553] Disarmed Default (Disarmed) __________________________________ [554] Armed Default (Armed) __________________________________ 16 HSPA(3G) Alarm Communicator Installation Guide [555] Automatic Disarming Default (Automatic Disarming) __________________________________ [556] Automatic Arming Default (Automatic Arming) __________________________________ [557] Automatic Arming Cancelled Default (Automatic Arming Cancelled) __________________________________ [558] Late to Open Default (Late to Open) __________________________________ [559] Late to Close Default (Late to Close) __________________________________ [560] Disarmed After Alarm Default (Disarmed After Alarm) __________________________________ [561] Alarm Occurred After Arming Default (Alarm Occurred After Arming) __________________________________ [562] Exit Fault Default (Exit Fault) __________________________________ [563] Cold Start Default (Cold Start) __________________________________ [564] Armed With Zones Bypassed Default (Armed With Zones Bypassed) __________________________________ [565] Zone Bypassed Default (Zone Bypassed) __________________________________ [566] Zone Unbypassed Default (Zone Unbypassed) __________________________________ [567] Burglary Verified Default (Burglary Verified) __________________________________ [568] Burglary Not Verified Default (Burglary Not Verified) __________________________________ [569] Alarm Cancelled Default (Alarm Cancelled) __________________________________ [570] Holdup Verified Default (Holdup Verified) __________________________________ [571] Walk Test Begin Default (Walk Test Begin) __________________________________ [572] Walk Test End Default (Walk Test End) __________________________________ [573] System Test Default (Test Message) __________________________________ [574] Periodic Test Transmission Default (Periodic Test) __________________________________ [575] Periodic Test With Trouble Default (Periodic Test With Trouble) __________________________________ [576] DLS Remote Programming Begin Default (Remote Programming Begin) __________________________________ [577] DLS Remote Programming End Default (Remote Programming End) __________________________________ [578] SA Remote Programming Begin Default (Remote Programming Begin) __________________________________ [579] SA Remote Programming End Default (Remote Programming End) __________________________________ [580] Installer Lead In Default (Local Programming Begin) __________________________________ [581] Installer Lead Out Default (Local Programming End) __________________________________ [582] Firmware Update Begin Default (Firmware Update Begin) __________________________________ [583] Firmware Update Successful Default (Firmware Update Successful) __________________________________ [584] Firmware Update Fail Default (Firmware Update Fail) __________________________________ [585] Delinquency Default (Delinquency) __________________________________ [586] Keypad Lockout Default (Keypad Lockout) __________________________________ [587] Event buffer 75% full Default (Event Buffer Near Full) __________________________________ [591] FTC Trouble Default (fail to communicate trouble) __________________________________ [592] FTC Restore Default (fail to communicate restore) __________________________________ [593] Panel Absent Trouble Default (Panel Communications Trouble) __________________________________ [594] Panel Absent Trouble Restore Default (Panel Communications Restore) __________________________________ [595] Module Reprogramming Default (Communicator Programming Updated) __________________________________ 17 HSPA(3G) Alarm Communicator Installation Guide [596] Firmware Update Default (Communicator Programming Updated) __________________________________ [600] Module Default (Module) __________________________________ [601] Stay Arm Default (Stay Arm) __________________________________ [602] Away Arm Default (Away Arm) __________________________________ [603] Night Arm Default (Night Arm) __________________________________ [604] Disarm Default (Disarm) __________________________________ [605] Activate Command Output 1 Default (Activate Command Output 1) __________________________________ [606] Activate Command Output 2 Default (Activate Command Output 2) __________________________________ [607] Activate Command Output 3 Default (Activate Command Output 3) __________________________________ [608] Activate Command Output 4 Default (Activate Command Output 4) __________________________________ [609] Deactivate Command Output 1 Default (Deactivate Command Output 1) __________________________________ [610] Deactivate Command Output 2 Default (Deactivate Command Output 2) __________________________________ [611] Deactivate Command Output 3 Default (Deactivate Command Output 3) __________________________________ [612] Deactivate Command Output 4 Default (Deactivate Command Output 4) __________________________________ [613] Bypass Default (Bypass) __________________________________ [614] Unbypass Default (Unbypass) __________________________________ [615] Status Request Default (Status Request) __________________________________ [616] Alarm Memory Request Default (Alarm Memory Request) __________________________________ [617] Help Default (Help) __________________________________ [618] Pay As You Go Balance Request Default (Balance Request) __________________________________ [619] Keypad Message Default (Keypad Message) __________________________________ [621] Function Successful Default (Successful) __________________________________ [622] Function Failure Default (Unsuccessful) __________________________________ [623] Invalid Command Default (Invalid Command) __________________________________ [624] System Stay Armed Default (Stay Armed) __________________________________ [625] System Away Armed Default (Away Armed) __________________________________ [626] System Night Armed Default (Night Armed) __________________________________ [627] System Disarmed Ready Default (Disarmed Ready) __________________________________ [628] System Disarmed, Not Ready Default (Disarmed Not Ready) __________________________________ [629] System In Alarm Default (is in Alarm) __________________________________ [630] Trouble Label Default (Service is Required) __________________________________ [631] No Alarms in Memory Default (No Alarms in Memory) __________________________________ [632] Pay As You Go Balance Default (Pay as you go balance:) __________________________________ [633] Pay As You Go Message Default (*123#) __________________________________ [634] Response Code Default (Response Code) __________________________________ [651] Integration Identification Number |____|____|____|____|____|____|____|____|____|____|____|____| [652] Integration Access Code |____|____|____|____|____|____|____|____| 18 HSPA(3G) Alarm Communicator Installation Guide [663] Integration Toggle Option 2 |____| [1] Integration Over Serial (ON). |____| [2] Integration Over Cellular (OFF). |____| [3] Integration Over Ethernet (OFF). |____| [4] Reserved. |____| [5] Integration Proto